Materials Testing Fixtures is our core business. In structural engineering sector has continuously looking for materials that exhibit low densities and at the same time good strength, good stiffness, good abrasion behavior and impact, and are not easily susceptible to corrosion. The knowledge of the mechanical and physical characteristics of a material is the first step for a correct evaluation of the performance of the exercise component.
In research and development are frequently required materials testing fixture for the execution of tests that are not the standard kit for testing machines.
The standard equipment marketed, in accordance with regulations UNI, EN, ISO, ASTM, DIN, BS, AF, are made Carbon Steel , Stainless steel or metal alloys (nickel alloys) so as to give the product high performance, even at high temperatures and minimize side effects such as corrosion and oxidation in normal ambient laboratory conditions.
We produce a wide range of test equipment for the testing of materials made in accordance with standard devices and the customer specifications.
Download PDF
Download PDF A sandwich panel or the core material itself can be tested in shear parallel to the flatwise plane. The fixture can be used to apply either a tensile or a compressive loading, although a tensile loading is most commonly utilized in order to eliminate buckling as a potential …
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF The basic types of mechanical wedge grips are two. In both cases the gripping members move and wedges remain stationary while it is clamped on the sample, or wedges move tightening the sample and bodies of the handles remain stationary. The “simple” wedge grips are slightly easier to …
Download PDF
Download PDF According to Federal Test Method 406, Method 1041, this double cutting testing fixture is intended for use in the determination of the shear strength of plastic materials. However, it is possible to test any material that the device is strong enough to handle. Is used a cylindrical specimen …
Download PDF This fixture satisfies the requirements of ASTM D 5961 and has also been adopted by Composite Materials Characterization, Inc. as their standard fixture. This device consists of bushings located in housings that can be screwed and to accommodate different thickness specimens. The testing principle is the same for both …
Download PDF Thanks to this fixture, it is possible to test, double-edged, typically metal fasteners of various types and dimensions. A hardened tool steel blade, having an accurately toleranced cutout of the diameter of the fastener to be tested is inserted in a fastener support fork, having similar cutouts. There …
Download PDF
Download PDF
Download PDF
Download PDF Split disk and ring segment tensile tests, properly interpreted, provide reasonably accurate information with regard to the apparent tensile strength of plastic pipe when employed under conditions approximating those under which the tests are made. ASTM Standard D 2290 originally included several procedures for testing ring specimens. Procedure …
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF This method describes the temperature retraction procedure for rapid assessment of crystallization effects. In addition, it serves to compare the properties of the viscoelastic rubber materials at low temperatures and gummy. This method is very useful to make a selection of materials suitable for low-temperature service. A small …
Download PDF
Download PDF
Download PDF
Download PDF Since they have enlarged ends and reduced central cross sections, Split collar grips are typically used to tensile test round bar specimens. To aid in minimizing induced bending in the specimen, can be built spherical seats. There are a wide variety of specimen sizes and configurations in use. …
Download PDF These test methods provide acceptable procedures for quality control purposes and for the determination of engineering characteristics. The equipment consists of two pulleys which stretch the O-ring to failure. To minimize the local stresses induced in the sample due to frictional forces, the standard provides that a spool …
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF
Download PDF There are four strips of tabbing material to maintain in proper alignment. A typical fixture consists of two plates, aligned with each other via pins in the base plate that slip into close-fitting mating holes in the cover plate. Usually the plates are manufactured of high-strength, anodized aluminum, …
Download PDF Code: P023-16 BU: Industrial Engineering Customer: CNR Time: 1 Month Author: Luigi Taddeo Design, analysis and development of a custom micro-actuated slide to perform optical microscope analysis of composite specimens. The technology allows the movement of the specimen placed on the slide in the order of microns thanks to the …
Download PDF Code: P008-17 BU: Industrial Engineering Customer: Saint-Gobain Time: 1 Month Author: Francesco Caraviello Design and realization of a control tooling to test the design of a Solaris Urbino bus glass. Bottom of the tool made of aluminum, while the upper one, which includes the shape area, is made up …
Download PDF Biaxial Test Fixture has been developed for loading an in-plane specimen simultaneously in two principal directions. Fixture is designed for use with an universal testing machine Use of the fixture should require no modifications of the test machine Alignment of the fixture should be considered so that no bending …
Download PDF Materials Testing Fixtures is our core business. In structural engineering sector has continuously looking for materials that exhibit low densities and at the same time good strength, good stiffness, good abrasion behavior and impact, and are not easily susceptible to corrosion. The knowledge of the mechanical and physical …
Download PDF The ideal candidate should have the following skills: 1- at least one year of experience in the automotive field; (senior profiles are warm welcome) 2- knowledge of can bus or fpga and related tools (canoe, canalyzer, doors, canape,etas inca) 3- knowledge of matlab or simulink or c, c++ …
Download PDF This test method covers the determination of the delami- nation strength (tensile node-to-node bond strength) of honey- comb core materials. Following the possible choices to be ordered. Test Standard ASTM C363 Maximum Load 4,5 kN Temperature Range da -80 °C a 149 °C Mounting 1/2”-13 threaded couplings …